Arcam AV888 Manual de usuario

1Custom Installation Notes:Serial programming interface andIR remote commands forArcam AVR500/AVR600/AV88823425MENU OK DIRECT DISPLAY ZONE MUTEMODEINP

10Input Command Specifications Video selection (0x0A)Changes the video input. Returns invalid (0x85) if OSD is showing setup screen.ExampleCommand/res

11Output Command SpecificationsSet/Request Volume (0x0D)Set or request the volume of a zone.is command returns the volume even if the zone requested

12Request decode mode status — 2ch (0x10)Request the decode mode for two-channel material in zone 1.ExampleCommand/response sequence to request the de

13Set/request Video Output Resolution (0x13)Set/request the Video Output Resolution of zone 1.ExampleCommand/response sequence to request the video ou

14Menu Command SpecificationsRequest menu status (0x14)Request which (if any) menu is open in the unit.ExampleCommand/response sequence to request whi

15Request DAB/Sirius station (0x18)Request the current DAB/Sirius station selected. If the DAB/Sirus is not selected on the given zone an error 0x85 i

16Request preset details (0x1B)Request details of tuner presets.ExampleCommand/response sequence to request preset 1 where the response is a preset on

17Setup Adjustment Command SpecificationsTreble Equalisaton (0x35)Adjust the amount of treble equalisation. ExampleCommand/response sequence to set th

18Dolby Volume (0x38)Control the status of the Dolby volume system.ExampleCommand/response sequence to turn the Dolby Volume system on in Movie mode:C

19Balance (0x3B)Adjust the balance control.ExampleCommand/response sequence to set the balance to -3:Command: 0x21 0x01 0x3B 0x01 0x83 0x0D Response

2ContentsIntroduction ...3Conventions ...

20Dolby Pro Logic II Panorama (0x3E)Turn on/off the Panorama setting of the Dolby Pro Logic II processor.ExampleCommand/response sequence to turn Dolb

21Compression (0x41)Adjust the dynamic range compression setting.ExampleCommand/response sequence to set compression to On/Auto:Command: 0x21 0x01 0

22Request incoming audio format (0x43)Request the incoming audio format.ExampleCommand/response sequence to request the incoming audio format, where t

23Request incoming audio sample rate (0x44)Request the incoming audio sample rate.ExampleCommand/response sequence to request the incoming audio sampl

24Set/Request Contrast (0x47)Set/Request the contrast control value.ExampleCommand/response sequence to set the contrast to 4:Command: 0x21 0x01 0x4

25Set/Request Edge Enhancement (0x4A)Set/Request the Edge Enhancement value.ExampleCommand/response sequence to set the Edge Enhancement value to ‘Med

26Set/Request Block Noise Reduction (0x4D)Set/Request the Block Noise Reduction value.ExampleCommand/response sequence to set the Block Noise Reductio

27Set/Request Output Frame Rate (0x50)Set/Request the video output frame rate.ExampleCommand/response sequence to set the frame rate to Auto:Command:

28Function RC5 code [system-command] RC5 code (Data1 - Data2)Decimal HexadecimalStandby 16-12 0x10 - 0x0CSelect Phono 16-1 0x10 - 0x01Select AV 16-2

29Advanced Functionsese RC5 codes are not present on the supplied remote control but have been created for custom install use. In order for theAVR500

3Command and response formatsCommunication between the remote controller (RC) and theAVR500/AVR600/AV888 takes the form of sequences of bytes, with al

30A&R Cambridge Ltd, Pembroke Avenue, Waterbeach, CAMBRIDGE CB25 9QR, EnglandSH217E Issue 623425+44 (0)1223 203200 http://www.arcam.co.uk/extra

4AMX Duet™ SupporteAVR500/AVR600/AV888 shall be fully compatible with AMX Duet™ Dynamic Device Discovery Protocol (DDDP) e following description of

5System Command SpecificationsPower (0x00)Request the stand-by state of a zone.ExampleCommand/response sequence to request the power state of zone 1 w

6FM genre (0x03) Request information on the current station programme type from FM source in a given zone. If FM is not selected on the given zone an

7Save/Restore secure copy of settings (0x06) Force a restore of the secure copy of the settings. Note: If no secure copy has been made, this command

8Display Information Type (0x09)Set the display information type (where applicable).ExampleCommand/response sequence to set the display text to show t

9COMMAND:Byte: Description:St 0x21 Zn Zone numberCc 0x1DDl 0x01Data 0xF0Et 0x0DRESPONSE:Byte: Description:St 0x21 Zn Zone numberCc 0x1DAc Answer codeD